433Mhz 100mW Radio Telemetry Module

  1. This Radio Telemetry Module is of 433Mhz
  2. Air data rates up to 250kbps
  3. The range is approx 1 mile (1.6 Km)
  4. MAVLink protocol framing and status reporting
  5. Frequency hopping spread spectrum (FHSS)
  6. Adaptive time division multiplexing (TDM)
  7. Support for LBT and AFA
  8. Micro-USB port
  9. Adaptive flow control when used with APM
  10. Based on the HopeRF HM-TRP radio module, featuring a SiLabs Si1000 RF microcontroller.

Description

This 433MHz 100mW Radio Telemetry Module V2 Kit is based on the 3DR Telemetry Kit and runs the same firmware on board, making it 100% compatible. This firmware used by 3D Robotics is completely open source. This is why it is available in its own version of Unmanned Tech.

The Unmanned Telemetry Kit is compatible with Ardupilot or Pixhawk-based systems and easily adds a bi-directional telemetry link between the drone and ground station. It comes with full support and warranty because it is a product that is confident in its functionality and reliability.

New and improved V2 of the Unmanned Telemetry Kit. Full features and specs are listed below, but the main feature is that both the air module and base module are now interchangeable, each fitted with a USB connector and a DF13 connector.

I also recommend buying a 6-pin to 6-pin cable as it’s easier and better than using the supplied cable when connecting to the Pixhawk.

Also check our wide range of  flight controllersDrone transmitter and receiver and other good quality drone parts .

Note: Product image may change in terms of design.

 

This telemetry only could use with APM compatible control board.

As we have some variations in the color of connecting cable, we will be shipping it randomly to our customers.

Features :

  1. Very small size & Lightweight (under 4 grams without antenna)
  2. Transparent serial link
  3. MAVLink protocol framing and status reporting
  4. Frequency hopping spread spectrum (FHSS)
  5. Adaptive time division multiplexing (TDM)
  6. Support for LBT and AFA
  7. Configurable duty cycle
  8. Interchangeable air and ground modules
  9. Micro-USB port
  10. 6-position DF13 connector
  11. 100 mW maximum output power (adjustable)
  12. Based on HopeRF’s HM-TRP module
  13. RP-SMA connector
  14. 2-way full-duplex communication through adaptive TDM
  15. UART interface
  16. Transparent serial link
  17. MAVLink protocol framing
  18. Frequency Hopping Spread Spectrum (FHSS)
  19. Configurable duty cycle
  20. Error correction corrects up to 25% of bit errors
  21. Configurable through Mission Planner and APM Planner
  22. Built-in error correcting code (can correct up to 25% data bit errors)
  23. The demonstrated range of several kilometers with a small Omni antenna
  24. Can be used with a bi-directional amplifier for even more range
  25. AT commands for radio configuration
  26. RT commands for remote radio configuration
  27. Adaptive flow control when used with APM
  28. Based on the HopeRF HM-TRP radio module, featuring a SiLabs Si1000 RF microcontroller.

Specifications:

Frequency(MHz) 433
Rated Power (W) 100mW
Range(m) 1600
Receive Sensitivity(dBm) -121
Serial Interface 3.3V UART
Air Data Rates(kbps) 250
Operating Current (A) 1.1
Voltage(V) 3.6 to 7
Operating Temperature (°C) -10 to 85
Weight(gm) 36

Package Includes :

1 x 3DR Radio Telemetry with the case and Tx and Rx Antenna.2 x cables (APM/PIX).2 x 3.5dbi antennas.

Reviews

There are no reviews yet.

Be the first to review “433Mhz 100mW Radio Telemetry Module”

Your email address will not be published. Required fields are marked *

X
Open chat
1
Contact supplier
Scan the code
Connecting Vdronetech
I want to make an inquiry for this 433Mhz 100mW Radio Telemetry Module. Lets discuss the best price.